Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN How To

Introduction

What is a VLAN? Is it some sort of highly expensive technology or virtual reality? Not at all. VLANs are relatively simple, yet they offer a wide variety of options and capabilities to improve your network.

VLAN, or Virtual LAN, is a technology that enables dividing a physical network into logical segments at Layer 2. Functionally, VLANs enable a network administrator to partition a network into separate, independent networks. There are many reasons to separate a network into VLANs, and numerous options to consider.

While a useful technology for small LANS, VLANs are often deployed in large networks, too. In larger networks, VLANs are sometimes used to join physically separate LANs or LAN segments into a single logical LAN.

The goal of this article is to explain and discuss VLANs, including why you should consider using VLANs in a smaller network. I'll also walk through a configuration example showing how to configure a VLAN-aware switch to create separate LAN segments.

VLANs and Switches

If you have more than one device on your network, you probably have a switch. A switch is a simple device that operates at Layer 2 of the OSI model, forwarding data frames from one device to another based on their hardware or MAC (Media Access Control) address. The basic Layer 2 switch does not care or know about IP addresses, which operate at Layer 3.

Your switch may be a few ports built into your router, it may be a small unmanaged (non-configurable) switch such as the D-Link DGS-2205 shown in Figure 1. Or you may have a more advanced switch with VLAN capability, possibly referred to as a managed, "smart" or multilayer switch. Larger networks usually have multiple switches at numerous locations.

D-Link switch

Figure 1: D-Link switch without VLAN capability

As stated, switches pass data from one device to another based on their MAC addresses. The key question is, how does the switch know which MAC address is located on which port?

Even the simplest switch has a "learning ability" to read the MAC address of the devices connected, and store those MAC addresses in a table in memory. Switches "learn" by examining the source MAC address of every frame received. New MAC addresses learned on received frames are added to a table, creating in the switch's memory a mapping of MAC addresses to switch ports.

More LAN & WAN

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

x3mRouting Version 2.3.0 now available! 1 September, 2020Migrating from Version 1.0Version 2.0.0 Update Process - update instructionsVersion 2.0...
So I'm looking to save on my monthly cable bill by cutting out the modem rental fees and buying my own. Thing is, I don't know what router I need to g...
I have been running into an intermittent problem on multiple Asus Routers, all running Asus Merlin Ver 384.17. About once every couple of weeks, the r...
v2.5.1 Updated 2020-05-10 Run an NTP server for your network. Graphs available for NTP accuracy on the Addons page of the WebUI.Inspired by kvic's p...
I've tried configuring it with the ezprint setup and ive also tried LTR and after a day or two it just goes offline. I have to reboot the pc and rerun...

Don't Miss These

  • 1
  • 2
  • 3