Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN Reviews

PlugLink 200 Mbps Powerline Adapter w/ PoE
At a glance
ProductAsoka PlugLink 200 Mbps Powerline Adapter w/ PoE (PL9660-PoE)   [Website]
SummarySingle port HomePlug AV adapter supporting IEEE 802.3af Power over Ethernet
Pros• The convenience of powerline networking and PoE in one device
• Throughput holds up well over distance
Cons• Available only direct from Asoka in U.S.

Typical Price: $75

Introduction

The concept for Asoka's PlugLink PL9660-PoE powerline adapter is simple: take a 200 Mbps HomePlug AV powerline adapter, add an 802.3af Power Over Ethernet injector and put them both in a compact, affordable package. That's about all there is to it.

The PL9660-PoE is a bit large by today's compact powerline adapter standards, since it has to accommodate additional circuitry for its PoE function. But as the photo below illustrates, it is thoughtfully designed to occupy only one outlet of a standard U.S. duplex. The smaller device is a PlugLink PL9660-Q1 that Asoka sent as the PoE's test partner.

PlugLinks plugged in

PlugLinks plugged in

Everything you expect on a 200 Mbps HomePlug AV adapter is there as shown in the callout diagram below. Yes, the port is 10/100, not Gigabit Ethernet.

PlugLink PoE callouts

PlugLink PoE callouts

The smaller PL9660-Q1 doesn't have a reset button. Its Security button is on the top, flush with the top cover.

PlugLink Q1 callouts

PlugLink Q1 callouts

The Powerline Link / Activity light on both adapters supposedly implements the (what is now) standard Green / Yellow / Red throughput (actually link rate) color scheme. But I've yet to see the color actually change in this or any other adapter that allegedly supports this scheme.

Inside

The inside of the PoE version has two boards sandwiched together. You can't see the powerline devices in the photo below—it appears to be mostly power circuitry. When I downloaded and ran Asoka's PowerManager 1.89 utility, the PoE's Firmware version revealed an INT6000 MAC. The INT6000 is a fairly old 200 Mbps HomePlug AV MAC/PHY device dating from Intellon's pre-Atheros-acquisition days. It requires a separate front end, but I didn't take the adapter apart to find out which one.

PlugLink PoE inside

PlugLink PoE inside

The PlugLink Q1 version is a single level board, with a QCA-branded device clearly visible at the top middle of the photo. I looked for the smaller analog front end companion, but couldn't find it. The reason for this became clear when I checked the part number on the device: QCA6410.

PlugLink Q1 inside

PlugLink Q1 inside

The reason I couldn't find a separate front end chip is that the QCA6410 is a single-chip 200 Mbps powerline device announced at the beginning of 2012.

More LAN & WAN

Wi-Fi System Tools
Check out the new Wi-Fi System Charts, Ranker and Finder!

Featured Sponsors




Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Is there a post or write up on seting up a VPN for the 86u? I searched and went through 5 pages, but couldn’t find anything. I’ve never done it before...
I tried to use the router tool, but the drop down had 40 choices and i have no idea which to choose. I looked at the modems in order, but i dont no wh...
Hi allI just got a pair of ac86u to replace my trusty n66u. I used the n66u with an external hard drive hooked to it to stream movies to a Roku and h...
I'm looking for a router that would allow me to limit each user bandwidth allowance, prioritize specified applications and type of traffic per group o...
Anyone ever deal with / heard of Grandstream's WiFi AP's the GWN7610 http://www.grandstream.com/products/networking-solutions/wifi-access-points/produ...

Don't Miss These

  • 1
  • 2
  • 3