Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Introduction

Update 12/19/17 - NETGEAR WAC505 added
Update 12/4/17- Corrected DAP-2610 supports MU-MIMO

The objects of our attention

The objects of our attention
Note: This review has been updated to add the NETGEAR WAC505.
Note: Additional testing on these products can be found here.

It seems like more people are realizing the performance (and cost) advantages that building a Wi-Fi network with Ethernet-connected access points (APs) can provide. If you're fortunate enough to have a large/multi-level home with Ethernet where you need to locate access points, there really is no reason to mess with more expensive mesh Wi-Fi systems, Wi-Fi extenders or even big, expensive conventional routers.

When using multiple APs, 2x2 AC1200 devices are the sweet spot. They are relatively low cost and match the dual-stream capabilities of most devices you're likely to connect to your WLAN. So we rounded up the seven eight products listed below for test, ranging in cost from a low of around $60 to a high of around $160, with plenty of others hovering around the $100 mark.

  • D-Link DAP-2610
  • Edimax CAP1200
  • Linksys LAPAC1200
  • NETGEAR WAC505
  • Open Mesh A40
  • TP-Link EAP225
  • Ubiquiti UAP-AC-Lite
  • Zyxel NWA1123-ACv2

We wanted to include NETGEAR's WAC505 and EnGenius' EAP1300 in this roundup, but neither company provided sufficient review samples. We wanted to include EnGenius' EAP1300 in this roundup, but the company would not provide sufficient review samples.

All products have at least one gigabit Ethernet port and can be powered by 802.3af or 802.3at Power over Ethernet. It's important to pay attention to the difference if you're planning on using PoE. Devices designated 802.3at draw more power than those spec'd 802.3af. So you'll need 802.3at switches to power them.

This review will be in two parts. I'm covering the basic product descriptions, component breakdowns and chamber-based throughput vs. attenuation and peak throughput tests. Jim Salter will be following up with a review of each product's performance in a three-AP home setup.

The review format will have a mini-review with component analysis and key features of each product, followed by group performance analysis. Let's begin.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi all!I have PlayStation 4 Pro at home. As you may know Sony has an app / programm named PS4 Remote Play which lets users access PS4 remotely from th...
Been running this RT-AC86U for a little over a month now. 1st thing I did was to load Merlin firmware which seems to be running fine. A short while b...
Went to the in-laws (Home 1) to setup a new network today to replace their Shitty Sky hub and it's made a good difference but I need to go back tomorr...
HiAfter the upgrade from version .13 to .14, in the system log sometimes appears this message:Dec 15 14:38:08 kernel: pgd = ffffffc014024000Dec 15 14:...
I just replaced my Asus 1900P running Merlin with a Netgear r7800 running Voxel 1.0.2.72SF. So far it seems to be running well. Was curious if there a...

Don't Miss These

  • 1
  • 2
  • 3